Loading...
3 results
Search Results
Now showing 1 - 3 of 3
- Laboratory study on the behaviour of spent AA household alkaline batteries in incinerationPublication . Almeida, Manuel F.; Xará, Susana M.; Delgado, Julanda; Costa, Carlos A.The quantitative evaluation of emissions from incineration is essential when Life Cycle Assessment (LCA) studies consider this process as an end-of-life solution for some wastes. Thus, the objective of this work is to quantify the main gaseous emissions produced when spent AA alkaline batteries are incinerated. With this aim, batteries were kept for 1 h at 1273 K in a refractory steel tube hold in a horizontal electric furnace with temperature control. At one end of the refractory steel tube, a constant air flow input assures the presence of oxygen in the atmosphere and guides the gaseous emissions to a filter system followed by a set of two bubbler flasks having an aqueous solution of 10% (v/v) nitric acid. After each set of experiments, sulphur, chlorides and metals (As, Cd, Co, Cr, Cu, Fe, Hg, Mn, Ni, Pb, Sb, Tl and Zn) were analyzed in both the solutions obtained from the steel tube washing and from the bubblers. Sulphur, chlorides and metals were quantified, respectively, using barium sulfate gravimetry, the Volhard method and atomic absorption spectrometry (AAS). The emissions of zinc, the most emitted metal, represent about 6.5% of the zinc content in the batteries. Emissions of manganese (whose oxide is the main component of the cathode) and iron (from the cathode collector) are negligible when compared with their amount in AA alkaline batteries. Mercury is the metal with higher volatility in the composition of the batteries and was collected even in the second bubbler flask. The amount of chlorides collected corresponds to about 36% of the chlorine in the battery sleeve that is made from PVC. A considerable part of the HCl formed in PVC plastic sleeve incineration is neutralized with KOH, zinc and manganese oxides and, thus, it is not totally released in the gas. Some of the emissions are predictable through a thermodynamic data analysis at temperatures in the range of 1200–1300 K taking into account the composition of the batteries. This analysis was done for most of potential reactions between components in the batteries as well as between them and the surrounding atmosphere and it reasonably agrees the experimental results. The results obtained show the role of alkaline batteries at the acid gases cleaning process, through the neutralization reactions of some of their components. Therefore, LCA of spent AA alkaline batteries at the municipal solid waste (MSW) incineration process must consider this contribution.
- Laboratory study on the leaching potential of spent alkaline batteriesPublication . Xará, Susana M.; Delgado, Julanda N.; Almeida, Manuel F.; Costa, Carlos A.Four different leaching tests were carried out with spent alkaline batteries as an attempt to quantify the environmental potential burdens associated with landfilling. The tests were performed in columns filled up with batteries either entire or cross-cut, using either deionized water or nitric acid solution as leachant. In a first set of tests, the NEN 7343 standard procedure was followed, with leachant circulating in open circuit from bottom to top through columns. These tests were extended to another leaching step where leachant percolated the columns in a closed loop process. Leachate solutions were periodically sampled and pH, conductivity, density, redox potential, sulphates, chlorides and heavy metals (As, Cd, Co, Cr, Cu, Fe, Hg, Mn, Ni, Pb, Sb, Tl and Zn) were determined in the samples. The results showed that the total amount of substances leached in tests with cross-cut batteries was higher than with entire ones; zinc and sulphates were the substances found the most in the leachate solutions. In general, the amount of substances dissolved in open circuit is higher than in closed loop due to the effect of solution saturation and the absence of fresh solution addition. Results were compared with metal contents in the batteries and with legal limits for acceptance in landfill (Decision 2003/33/CE and Decree-Law 152/2002). None of the metals were meaningfully dissolved comparatively to its content in the batteries, except Hg. Despite the differences in the experiment procedure used and the one stated in the legislation (mixing, contact time and granulometry), the comparison of results obtained with cross-cut batteries using deionized water with legal limits showed that batteries studied could be considered hazardous waste.
- Influence of the impact assessment method on the conclusions of a LCA study. Application to the case of a part made with virgin and recycled HDPEPublication . Simões, Carla L.; Xará, Susana M.; Bernardo, C. A.Recent legislation has stressed the need to decide the best end-of-life (EoL) option for post-consumer products considering their full life-cycle and the corresponding overall environmental impacts. The life cycle assessment (LCA) technique has become a common tool to evaluate those impacts. The present study aimed to contribute to the better understanding of the application of this technique, by evaluating the influence of the selection of the life cycle impact assessment (LCIA) method in its results and conclusions. A specific case study was chosen, using previous information related to an anti-glare lamellae (AGL) for highway use, made with virgin and recycled high-density polyethylene (HDPE). Five distinct LCIA methods were used: Eco-indicator 99, CML 2 (2000), EPS 2000, Eco-indicator 95 and EDIP 97. Consistent results between these methods were obtained for the Climate change, Ozone layer depletion, Acidification and Eutrophication environmental indicators. Conversely, the Summer smog indicator showed large discrepancies between impact assessment methods. The work sheds light on the advantages inherent in using various LCIA methods when doing the LCA study of a specific product, thus evidencing complementary analysis perspectives.